What Is a Roof Pitch Calculator?
A roof pitch calculator converts between the different ways of describing how steep a roof is, and uses the pitch to work out practical measurements for building and roofing. In the US and Canada, pitch is expressed as rise over a 12-inch run: a 6/12 roof rises 6 inches for every 12 inches horizontally. Elsewhere, roof slope is usually given as an angle in degrees or occasionally as a percentage. A 6/12 pitch equals 26.57° or 50%.
This free calculator converts between all of these, finds the pitch from any rise and run, and, given the building span, calculates the total rise, rafter length (with overhang), roof area and number of roofing squares. A diagram shows the slope, and a chart lists common pitches.
How to Calculate Roof Pitch
- Choose what you know: pitch, angle, percent, or rise and run.
- Enter the value to see all equivalents instantly.
- Add the building span (wall to wall) and overhang to get rise and rafter length.
- Add the roof length to calculate the total roof area.
Roof Pitch Formulas
- Pitch = rise ÷ run × 12 (e.g. 4 ft rise over 8 ft run = 6/12)
- Angle = arctan(rise ÷ run)
- Slope % = rise ÷ run × 100
- Rafter length = run × √(1 + (rise/run)²)
- Roof area = footprint area × area factor (the same √ term)
Common Roof Pitches
| Pitch | Angle | Typical use |
|---|---|---|
| 2/12 | 9.5° | Low-slope, sheds, porches (special roofing) |
| 4/12 | 18.4° | Ranch homes, minimum for standard shingles |
| 6/12 | 26.6° | Very common residential pitch |
| 8/12 | 33.7° | Traditional homes, good snow shedding |
| 12/12 | 45° | Steep, Tudor and Victorian styles, attic space |
Features
- Four input methodsPitch, degrees, percent or rise and run.
- Rafter lengthWith or without overhang.
- Roof areaIncluding overhangs, in ft²/m² and roofing squares.
- Area factorMultiply any footprint by it to get the sloped area.
- Visual diagramSee the slope drawn to scale.
- Feet or metresWorks with either unit system.
Why Roof Pitch Matters
Pitch affects almost every decision about a roof. It determines which roofing materials can be used: asphalt shingles need at least 2/12 to 4/12, metal and membrane systems suit low slopes, and slate or clay tiles usually need steeper pitches. It affects how quickly rain and snow run off, which matters in wet and snowy climates. It changes the amount of usable attic space and the look of the house. It also determines safety and cost: roofs steeper than about 7/12 or 8/12 usually need extra safety equipment, and installers charge more for them.
When estimating materials, remember that the sloped roof surface is always larger than the building's footprint. Multiply the footprint (including overhangs) by the area factor above. A 6/12 roof has about 12% more surface than its plan area, while a 12/12 roof has 41% more.
Measuring Pitch Without Climbing on the Roof
You can often measure pitch safely from inside the attic by placing a level against the underside of a rafter. Measure 12 inches along the level from the rafter and then the vertical distance up to the rafter's underside. From the ground, a smartphone inclinometer app held against a gable-end photo or an angle finder on a ladder at the eaves can give a good estimate. Enter the angle above to convert it.
Tip: for hip roofs, the common rafters use the same pitch as calculated here, while hip and valley rafters run at 45° in plan and are longer. Multiply the common run by 1.414 to get the hip run before applying the slope factor.
If you're ordering roofing, add 10–15% to the calculated area for waste, starter courses, ridge caps and cutting around valleys, chimneys and skylights.
Frequently Asked Questions
What angle is a 6/12 pitch?
26.57 degrees, or a 50% slope.
How do I measure my roof pitch?
Place a level horizontally against the roof (or rafter), measure 12 inches along the level, then measure vertically from that point to the roof surface. That vertical distance is the pitch.
What is the minimum pitch for shingles?
Most asphalt shingle manufacturers require at least 2/12 with special underlayment, and 4/12 for standard installation.
What is a roofing square?
100 square feet of roof surface. Shingles are commonly sold in bundles, with three bundles per square.
Does the rafter length include the ridge board?
No. Subtract half the ridge board thickness (measured horizontally) from the run for precise cuts.